若NVMe SSD在Windows安裝過程中未顯示，首先檢查BIOS/UEFI設置，確保其被正確識別并啟用，將存儲模式設為AHCI，必要時開啟CSM或調整Secure Boot狀態；其次使用含NVMe驅動的最新Windows安裝介質，并選擇正確的分區方案（UEFI選GPT，BIOS選MBR）；接著確認NVMe驅動器物理連接穩固，嘗試更換插槽或測試于其他系統中；最后通過安裝界面按Shift F10調出命令提示符，輸入diskpart后執行l(wèi)ist disk查看磁盤是否存在，如存在則用select disk #、clean及convert gpt/mbr初始化。多數情況下問題源于配置而非硬件故障。

If your NVMe SSD isn’t showing up during Windows installation, it can be frustrating, especially if you’re trying to set up a new system. The good news is that this issue is fairly common and often has straightforward fixes.

Check the BIOS/UEFI Settings

Before jumping into complicated solutions, start with the basics—your motherboard’s BIOS or UEFI settings. Sometimes, the NVMe drive won’t show up simply because it’s not enabled or configured correctly in the firmware.

• Make sure the NVMe drive is listed under storage devices in the BIOS.
• Check if Storage Mode is set to AHCI instead of RAID (especially on Intel chipsets). RAID mode may prevent detection unless drivers are injected during install.
• If there's an option for CSM (Compatibility Support Module), try enabling it temporarily. It helps with legacy boot compatibility.
• Also, ensure that Secure Boot is either enabled or disabled based on your installation media type—sometimes mismatched modes cause detection issues.

You don’t need advanced knowledge here; just go through each relevant setting and make sure they align with standard setup practices.

Use the Right Installation Media

Not all Windows installation USB drives are created equal. If you're using a version of Windows that doesn't include native NVMe drivers (older versions like Windows 10 1703 or earlier), your drive might not be recognized at all.

• Try using the latest Windows ISO from Microsoft. Newer versions usually have better hardware support.
• When creating the USB installer, use tools like Rufus or the official Media Creation Tool and ensure you're using the correct partition scheme:
  • For UEFI systems: GPT
  • For older BIOS systems: MBR

Some motherboards also require USB 3.0 or NVMe drivers to be injected manually into the installer. This is more common on older AMD X570 boards or some Intel Z390 models.

Connect the NVMe Drive Properly

This sounds obvious, but it’s worth double-checking. An NVMe SSD needs to be seated properly in the M.2 slot or U.2 connector, depending on your setup.

• Re-seat the NVMe drive to ensure solid contact.
• Confirm that the drive is getting power and isn’t loose.
• If possible, test the NVMe drive in another system to confirm it’s working.
• Try a different M.2 slot if your motherboard has more than one.

Also, some motherboards disable certain M.2 slots when specific PCIe slots are occupied. Refer to your motherboard manual to see if that’s happening in your case.

Access Disk Management or Use Command Prompt

Sometimes, the NVMe drive is actually detected by the Windows installer, but just not visible in the initial setup screen. You can check this by opening a command prompt from the installer:

1. Press Shift F10 during installation to open the command prompt.
2. Type diskpart and hit Enter.
3. Then type list disk to see if your NVMe drive appears.

If it does show up but isn’t initialized:

• Use select disk # (replace # with the disk number)
• Then run clean, followed by convert gpt (or convert mbr if you're using CSM)

Alternatively, after installing Windows, you can go to Disk Management and initialize the drive if needed.

In most cases, the NVMe SSD not being detected is due to configuration rather than a hardware failure. Double-checking BIOS settings, using updated installation media, ensuring proper physical connections, and verifying via DiskPart can resolve most issues. It’s not rocket science—it just takes a bit of patience and methodical troubleshooting.

基本上就這些。

以上是如果在Windows安裝過程中未檢測到NVME SSD，該怎么辦？的詳細內容。更多信息請關注PHP中文網其他相關文章！